
Centauri Carbon 2 Exhaust Vent Kit: Vent Your CC2 Fumes Outdoors
The KODNA CC2 Printer Vent Kit is a 16-part printable Centauri Carbon 2 exhaust vent system. It routes your printer’s fumes up like a chimney, across the ceiling and out through the wall, with no drilling into the printer. Every part prints on the CC2 itself, in STL and 3MF.
Why vent your 3D printer fumes outside
Printing ABS, ASA or nylon fills a room with fumes. An enclosure keeps heat in, but the air still has to go somewhere. This kit sends it outdoors through a sealed 4-inch duct run you print yourself.
Magnetic CC2 exhaust adapter
- Four 10 x 3 mm magnets hold the adapter over the rear exhaust fan.
- Screw holes match the factory screws if you want it permanent.
- The 4-inch outlet plugs straight into the pipes, elbows or laundry hose.
Modular 4 inch 3D printer exhaust duct
- One joint standard: every pipe, elbow, coupler and hose adapter plugs into every other.
- Standard 4-inch laundry/dryer hose slides over the flex adapters wherever you need a bend.
- Every part fits a 254 x 254 mm plate, already oriented to print.
Soldering fume extractor branch
A 90° tee splits off a branch to your soldering bench, and a reducer steps it down to 2.5-inch hose. When you’re only printing, a cap plug closes it off.
Pest-proof outdoor wall vent
The wall vent screws over a 4-inch hole. Its hood has 4.95 mm slots that keep mice out, and one set of screws holds both the flange and the hood.
What’s in the Centauri Carbon 2 vent kit
- Printer adapter – magnetic mount with a 4-inch outlet
- Straight pipes – 240 mm and 120 mm
- Couplers – female-female / male-male
- Elbows – 45° (two make a 90°) and 90°
- 90° tee – soldering-fume branch
- Reducer – 4-inch to 2.5-inch hose (63 mm end)
- Cap plug – closes the branch
- Flex hose adapters – female and male
- Wall vent – flange with through-wall tail, plus outdoor hood
- U-strap bracket – holds pipe to a wall or ceiling
Hardware you’ll need
- 4 x N52 disc magnets, 10 x 3 mm
- 4-inch laundry/dryer hose and 4-inch hose clamps
- Foil HVAC tape to seal joints
- #8 or 4 mm screws for brackets and the wall vent
- Optional: a 4-inch inline duct fan for long runs or the soldering branch
Print settings
PETG for indoor parts, ASA for the outdoor flange and hood. Walls are 2.4 mm, so 5-6 perimeters print them solid. Only the 90° tee and 90° elbow need tree supports. Press the magnets in after printing; the pockets open on the printer side.
The 3MF files contain the oriented models only, with no printer profile. If your slicer asks, choose “Load Model Only” (Elegoo Slicer, Orca) and use your own settings.
Centauri Carbon 2 exhaust vent FAQ
Does it fit the original Centauri Carbon?
No. The adapter is shaped for the Centauri Carbon 2. The 4-inch pipes fit any 4-inch duct system.
Do I have to drill or modify the printer?
No. Four magnets hold the adapter; the screw holes are optional.
Is the printer’s fan strong enough?
For a short run, yes. Add a 4-inch inline fan for long runs or when using the soldering branch.
Will the magnets affect the printer or Wi-Fi?
No. Small static magnets don’t affect electronics or Wi-Fi.
Can I use dryer hose?
Yes. Standard 4-inch laundry/dryer hose fits the flex adapters, secured with a hose clamp.
Get the CC2 Printer Vent Kit
Download the free STL + 3MF files on Printables
Keep the outside vent away from windows, doors and air intakes, and check local building rules before cutting a wall. Not affiliated with or endorsed by ELEGOO.